Glossary.
Plain-language definitions of the carbon, certification, performance, and materials terms you'll see on data sheets and specifications.
304 terms shown
A
- A1–A3Product stage
- The lifecycle modules covering raw material supply, transport to the factory, and manufacturing. It is the most widely reported carbon scope and the baseline Matera uses to compare products.Read the guide on A1–A3See also Lifecycle modules, Cradle to gate
- Abrasion classAC rating
- How well a laminate floor's surface stands up to wear under EN 13329, from AC1 (light domestic use) to AC6 (heavy commercial use). It measures wear only, not impact or stain resistance.
- AcidificationAP
- An EPD indicator for emissions that make soil and water more acidic, as with acid rain.Read the guide on AcidificationSee also EPD
- Adobe
- Sun-dried bricks of earth, often mixed with straw, laid with earth mortar. They have low processing energy but need protection from persistent wet.Read the guide on AdobeSee also Cob, Unfired clay
- ADPAbiotic depletion potential
- An EPD indicator for the depletion of non-living resources, such as minerals and fossil fuels.Read the guide on ADPSee also EPD
- AgBB
- A German scheme for testing emissions from building products into indoor air.Read the guide on AgBBSee also VOC, EMICODE
- Air permeability class
- How much air leaks through a window or door under test pressure, from class 1 to class 4 under EN 12207. Class 4 is the tightest.See also Airtightness, Watertightness class, Wind resistance class
- Airflow resistivity
- How strongly a porous material resists air passing through it, in kPa·s/m². It is a key property of insulation used for sound absorption.See also Sound absorption (αw)
- AirtightnessAir permeability
- How little uncontrolled air leaks through a building's fabric, measured with a pressure test. Better airtightness reduces heat loss but needs a planned ventilation strategy to go with it.Read the guide on AirtightnessSee also Passivhaus, Breathable
- Apparent porosity
- The share of a material's volume made up of pores open to the surface, as a percentage. It affects water uptake and frost resistance in brick, stone, and concrete.See also Water absorption, Frost resistance
- Application thickness
- How thickly a plaster, render, coating, or adhesive should be applied, per coat or in total. Going outside the range can cause cracking or poor performance.
- Approved Document BPart B, fire safety
- Statutory guidance on meeting the fire safety requirements of the Building Regulations in England. It includes limits on combustible materials in the external walls of certain tall buildings.See also Euroclass, Building Safety Act 2022
B
- B Corp
- A certification of a whole company's social and environmental performance, accountability, and transparency. It describes the business, not any individual product.Read the guide on B Corp
- BBABritish Board of Agrément
- A UK body that certifies construction products for fitness for purpose and durability. BBA certificates cover performance rather than environmental impact.Read the guide on BBA
- BES 6001
- A BRE standard for the responsible sourcing of construction products, covering organisational management, supply chain, and environmental and social factors.Read the guide on BES 6001See also Responsible sourcing, BREEAM
- BIMBuilding Information Modelling, Revit, IFC, DWG
- Digital models of a building that hold both its geometry and its data. Suppliers often provide product files in formats such as Revit (.rfa), IFC, or DWG for designers to use.See also Uniclass
- Binder type
- What holds a product's fibres or particles together, such as lime in hempcrete, or polyester or starch in insulation batts. A synthetic binder lowers the bio-based share and can make the product harder to compost or recycle.Read the guide on Binder typeSee also Bio-based content, Hempcrete, Lime plaster, mortar, and render
- Bio-based
- Made wholly or partly from living sources such as plants, trees, or animal fibres. It does not automatically mean low impact, or that a product is free of synthetic additives.Read the guide on Bio-basedSee also Biogenic carbon, Rapidly renewable
- Bio-based content
- The percentage of a product made from biological sources. Check whether the figure is by mass and whether it has been tested or simply declared.See also Bio-based
- Biogenic carbon
- Carbon absorbed from the atmosphere by plants as they grow and held in products such as timber, hemp, and straw. It is released again if the material rots or burns, so EPDs report it separately.Read the guide on Biogenic carbonSee also Sequestration, Bio-based
- Blue AngelBlauer Engel
- Germany's government-backed ecolabel, used on products including paints, flooring, and insulation, with particular attention to emissions and health.Read the guide on Blue AngelSee also EU Ecolabel, Type I ecolabel
- BOF steelBasic oxygen furnace
- Steel made mainly from iron ore and coal-based ironmaking, with some scrap. It generally has a much higher carbon footprint than EAF steel.Read the guide on BOF steelSee also EAF steel
- BreathableVapour open
- Describes a construction that lets water vapour pass through and dry out, which matters especially in older solid-walled buildings. It refers to moisture movement, not to air leaking through the wall.Read the guide on BreathableSee also Vapour resistance (μ), Hygroscopic, Interstitial condensation
- BREEAM
- A widely used UK-origin method for assessing a building's sustainability, rated from Pass to Outstanding. Materials can contribute through credits for lifecycle impacts and responsible sourcing.Read the guide on BREEAMSee also LEED, BES 6001
- Brinell hardnessHB
- A metal's resistance to indentation, measured by pressing a hard ball into its surface. A higher number means a harder metal.See also Vickers hardness
- Building control
- The process of checking building work against the Building Regulations, carried out by local authority or registered private inspectors.See also Part L
- Building Safety Act 2022
- UK legislation passed after the Grenfell Tower fire, creating a stricter regime for higher-risk buildings and clearer duties for those who design and build them.See also Approved Document B
- By-product
- A secondary output of another industrial process, such as slag from ironmaking or sawdust from milling, used as a raw material rather than discarded.See also GGBS
C
- Calcined clayLC3
- Clay heated to make it reactive, used to replace part of the clinker in cement. It is the basis of limestone calcined clay cement (LC3).Read the guide on Calcined claySee also SCM, Portland cement
- Carbon benchmark
- A typical carbon figure for a type of material, used as a point of comparison or as a stand-in when a product has no data of its own. It describes the category, not the specific product.Read the guide on Carbon benchmarkSee also Generic data, ICE Database
- Carbon budget
- A limit on the carbon a project can emit, usually in kgCO₂e/m², which is then shared between building elements.Read the guide on Carbon budgetSee also Whole life carbon, LETI
- Carbon footprint
- The total greenhouse gas emissions caused by a product, company, or activity. The figure means little without knowing what it includes, so check its boundary.See also System boundary, CO₂e
- Carbon negativeClimate positive
- A claim that a product stores or removes more carbon than it emits. For bio-based materials, it often depends on counting stored carbon and leaving out end-of-life emissions.See also Biogenic carbon, Sequestration
- Carbon neutralCarbon Neutral Certified
- A claim that the emissions of a product or company have been balanced out, usually through offsets. Check what was measured and how much was actually reduced before the offsets were applied.See also Carbon offset, Net zero
- Carbon offset
- A credit representing emissions reduced or removed elsewhere, such as through tree planting. Offsets compensate for emissions rather than avoiding them, and their quality varies widely.See also Carbon neutral, Net zero
- Casein paintMilk paint
- A traditional paint using milk protein as a binder, typically supplied as a powder and mixed with water.Read the guide on Casein paintSee also VOC
- CDPH Standard Method
- A California test method for VOC emissions from building products. Many low-emission labels and LEED credits refer to it.Read the guide on CDPH Standard MethodSee also VOC, GREENGUARD
- CE and UKCA marking
- Marks declaring that a product meets the legal requirements for sale in its market. Great Britain currently accepts either mark on construction products. They are a regulatory baseline and say nothing about environmental performance.Read the guide on CE and UKCA markingSee also DoP
- Cellulose insulation
- Insulation made mainly from recycled paper, usually blown or dense-packed into cavities and treated for fire and pest resistance.Read the guide on Cellulose insulation
- Cement replacement
- The percentage of Portland cement in a mix replaced by other binders such as GGBS. A higher share usually lowers embodied carbon, but it can change setting and strength gain.Read the guide on Cement replacementSee also GGBS, PFA, SCM
- Chain of custody
- The documented trail of a certified material through each company that handles it, from source to final product. Without it, a product cannot carry an FSC or PEFC claim.Read the guide on Chain of custodySee also FSC, PEFC, Traceability
- Circular economy
- An approach that keeps materials in use for as long as possible through reuse, repair, and recycling, rather than a take-make-dispose model.Read the guide on Circular economySee also Design for disassembly, Reclaimed
- Clay paint
- Paint using natural clay as a binder or main ingredient, typically with a matt finish and good vapour openness.Read the guide on Clay paintSee also Breathable, VOC
- Closed-loop manufacturing
- A production process that feeds waste or used products back in as inputs for the same type of product.See also Circular economy, Pre-consumer recycled content
- CLTCross-laminated timber
- Large structural panels made by gluing layers of timber at right angles to one another, used for walls, floors, and roofs.Read the guide on CLTSee also Engineered timber, Glulam
- CO₂eCarbon dioxide equivalent
- A common unit that expresses the warming effect of different greenhouse gases as the equivalent amount of carbon dioxide. Carbon figures for materials are usually given as kgCO₂e per declared unit.Read the guide on CO₂eSee also GWP, Declared unit
- Coating mass
- The weight of protective coating per square metre on a metal, such as zinc on galvanised steel, in g/m². A heavier coating generally gives longer corrosion protection.
- Cob
- A traditional mix of subsoil, straw, and water, built up by hand into monolithic walls without formwork.Read the guide on CobSee also Adobe, Rammed earth
- Coefficient of thermal expansion
- How much a material grows or shrinks as its temperature changes, in µm/m·°C. It affects movement joints, especially where different materials meet.
- Commodity codeHS code, tariff code
- A customs classification used for import and export declarations, duties, and trade rules. You can check UK codes using the UK Trade Tariff.
- Compostability
- Whether a product breaks down into compost at the end of its life. Home compostable products do so in a garden heap, while industrially compostable ones need a controlled commercial facility.
- Compression set
- The permanent loss of thickness left after a sealant, gasket, or foam has been squashed and released, as a percentage. Lower means it recovers better.
- Compressive strength
- The load per unit area a material can take when squashed before it fails, measured in MPa. It is a key figure for concrete, masonry, and other load-bearing materials.
- Compressive stress at 10% deformation
- The pressure that squashes an insulation board by 10% of its thickness, in kPa. It indicates whether a board can carry loads such as a floor or flat roof.See also Compressive strength
- Condition grade
- The supplier's own assessment of a reclaimed item's state: as new, good, fair, or needs restoration. It is not a formal standard, so ask for photos of the actual stock.Read the guide on Condition gradeSee also Reclaimed, Previous use
- Consistence class
- How easily fresh concrete flows and can be placed, under BS EN 206. Slump classes run from S1 (stiff) to S5 (very fluid), and flow classes F1 to F6 cover more flowable mixes.See also Exposure class
- Contaminant checks
- Inspections or tests showing a reclaimed material is free of hazards such as lead paint, asbestos, old timber preservatives, or oil. Ask what was checked and how.Read the guide on Contaminant checksSee also Previous use, Reclaimed
- Cork
- The bark of the cork oak, harvested without felling the tree and used for insulation, flooring, and acoustic layers.Read the guide on Cork
- Corrosion category
- How corrosive the environment is where metal will be used, under ISO 12944-2, from C1 (very low, such as heated interiors) to C5 (very high, such as industrial or coastal sites) and CX (extreme, such as offshore). A coating or metal should be rated for the category it will face.See also Coating mass
- COSHHControl of Substances Hazardous to Health
- UK regulations requiring employers to assess and control exposure to hazardous substances. A COSHH assessment often draws on the product's Safety Data Sheet.See also Safety Data Sheet
- Coverage
- The area a quantity of product will cover, such as m² per litre of paint. Real coverage varies with the surface and the number of coats.
- CPRConstruction Products Regulation
- The rules for placing construction products on the market, including how their performance is declared. Great Britain and the EU now have separate versions, and reforms are under way in both.Read the guide on CPRSee also CE and UKCA marking, DoP
- Cradle to Cradle CertifiedC2C
- A product standard assessing material health, circularity, clean air and climate protection, water and soil stewardship, and social fairness, with achievement levels from Bronze to Platinum.Read the guide on Cradle to Cradle CertifiedSee also Circular economy
- Cradle to gate
- A lifecycle boundary running from raw material extraction to the point a product leaves the factory, equivalent to modules A1–A3.Read the guide on Cradle to gateSee also A1–A3, Cradle to grave
- Cradle to grave
- A lifecycle boundary running from raw material extraction to final disposal, covering modules A to C. It gives a fuller picture than cradle to gate but relies on more assumptions.Read the guide on Cradle to graveSee also Cradle to gate, Lifecycle modules
- Cullet
- Crushed recycled glass that is melted to make new glass or glass-based products, reducing the energy and raw materials needed.Read the guide on CulletSee also Float glass
- Curing time
- How long a product takes to reach its full strength or properties after setting. Loading or overcoating it too early can cause failures.See also Setting time, Working time
D
- Data quality
- How far a carbon figure can be trusted, based on its source, verification, age, and how specific it is to the product.Read the guide on Data qualitySee also Third-party verification, Generic data
- Declare
- An ingredient disclosure label from the International Living Future Institute, showing what a product is made of and whether it contains substances of concern.Read the guide on Declare
- Declared unit
- The quantity of product a carbon figure refers to, such as 1 kg, 1 m², or 1 m³. Two figures can only be compared directly once they are on the same unit.Read the guide on Declared unitSee also Functional unit, EPD
- Deconstruction
- Carefully dismantling a building so that its components can be reused, rather than demolishing it.Read the guide on DeconstructionSee also Design for disassembly, Pre-demolition audit
- Density
- Mass per unit volume, in kg/m³. It influences weight, thermal mass, and sound insulation, and for insulation it can also indicate rigidity.See also Thermal mass
- Design for disassembly
- Designing a building or product so it can be taken apart and its components reused, for example by using mechanical fixings instead of adhesives.Read the guide on Design for disassemblySee also Circular economy, Material passport
- Digital product passport
- A digital record of a product's composition, origin, and environmental information. The EU is introducing these for certain product groups.Read the guide on Digital product passportSee also Material passport
- DimensionsThickness, Width, Length, Depth, Diameter, Tile / panel size
- A product's physical size as supplied. Check whether figures are nominal or actual, and allow for joints and offcuts when working out quantities.
- DoPDeclaration of Performance
- A manufacturer's formal statement of a construction product's performance against its harmonised standard, which supports CE or UKCA marking. It differs from an EPD, which covers environmental impacts.Read the guide on DoPSee also CE and UKCA marking, EPD
- Downcycling
- Recycling a material into a lower-value use, such as crushing concrete into fill. It avoids landfill but loses much of the original material's value.Read the guide on DowncyclingSee also Upcycling
- Durability class (EN 350)
- A timber species' natural resistance to fungal decay, from class 1 (very durable) to class 5 (not durable). It applies to heartwood, as sapwood is usually less durable.See also Use class (treatment)
E
- EAF steelElectric arc furnace
- Steel made mainly by melting scrap using electricity. Its carbon footprint is generally much lower than BOF steel, though it depends on the electricity used and the scrap available.Read the guide on EAF steelSee also BOF steel, ResponsibleSteel
- Elongation at break
- How far a material stretches before it snaps, as a percentage of its original length. Higher figures indicate a more ductile or flexible material.
- EMASEco-Management and Audit Scheme
- The EU's environmental management scheme, which builds on ISO 14001 and adds a requirement for public environmental reporting.Read the guide on EMASSee also ISO 14001, EMS
- Embodied carbon
- The greenhouse gas emissions from making, transporting, installing, maintaining, and disposing of a material, as distinct from the emissions from running a building.Read the guide on Embodied carbonSee also Operational carbon, Upfront carbon, Whole life carbon
- EMICODE
- A label from Germany's GEV for flooring installation products, adhesives, and similar materials, based on low emissions. EC1 is its low-emission class.Read the guide on EMICODESee also VOC
- EMSEnvironmental management system
- An organisation's framework for managing and reducing its environmental impact. ISO 14001 is the best-known standard for one.Read the guide on EMSSee also ISO 14001, EMAS
- EN 15804
- The European standard setting the core rules for EPDs of construction products. Check the version on an EPD: results under EN 15804+A1 and +A2 are calculated differently and may not compare cleanly.Read the guide on EN 15804See also EPD, PCR
- EN 15978
- The European standard for assessing the environmental performance of whole buildings, which defines the lifecycle modules used in reporting.Read the guide on EN 15978See also Lifecycle modules, EN 15804
- EnerPHit
- The Passive House Institute's standard for retrofitting existing buildings, which is less demanding than full Passivhaus.Read the guide on EnerPHitSee also Passivhaus, Retrofit
- Engineered timber
- Wood products made by bonding layers or pieces of timber together for greater strength and stability. The term covers CLT, glulam, and laminated veneer lumber.Read the guide on Engineered timberSee also CLT, Glulam
- EPDEnvironmental Product Declaration
- A standardised, independently verified document reporting a product's environmental impacts across its lifecycle, based on an LCA. An EPD reports impacts; it does not by itself mean a product is low impact.Read the guide on EPDSee also LCA, EN 15804, Third-party verification
- EPSExpanded polystyrene
- A lightweight, rigid foam insulation made from expanded beads of oil-derived plastic.See also XPS, PIR
- EU Ecolabel
- The European Union's official voluntary environmental label, identified by a flower logo and awarded to products meeting lifecycle-based criteria.Read the guide on EU EcolabelSee also Blue Angel, Type I ecolabel
- EuroclassReaction to fire, fire rating, fire class
- The European classification of how a material behaves in a fire, from A1 (non-combustible) down to F, with extra ratings for smoke (s1–s3) and flaming droplets (d0–d2). It rates the material, not a whole wall or floor build-up.See also Approved Document B
- EutrophicationEP
- An EPD indicator for excess nutrients entering water or soil, which can cause algal blooms and harm ecosystems.Read the guide on EutrophicationSee also EPD
- Exposure class
- The conditions concrete will face, under BS EN 206 and BS 8500: X0 (no risk), XC (carbonation), XD (chlorides such as de-icing salt), XS (sea water), XF (freeze-thaw), and XA (chemical attack). It sets the minimum strength and cover the concrete needs.See also Strength class, Low-carbon concrete
F
- Fibre content
- The percentage of a product made up of its fibres, such as hemp or wood, with the rest being binders and additives. It helps show how much of a natural product is truly natural.
- Fibre or plant source
- The crop, tree, or animal a bio-based product's fibre comes from, such as hemp, flax, straw, wood, or sheep's wool.Read the guide on Fibre or plant sourceSee also Bio-based, Rapidly renewable
- Fire resistance
- How long a building element keeps doing its job in a fire, in minutes, under EN 13501-2. R is load-bearing capacity, E is integrity, and I is insulation, so REI 60 means all three for 60 minutes. It is different from reaction to fire, which the Euroclass covers.See also Euroclass, Approved Document B
- Fixing size
- The diameter and length of a screw, nail, or anchor, such as 5 × 60 mm. Metric bolts use an M number for the thread diameter, so M10 is 10 mm.
- Flaming droplets
- The part of a Euroclass rating that covers burning droplets falling from a material in a fire, from d0 (none) to d2 (most).See also Euroclass, Smoke class
- Flexural strength
- How much bending stress a material can take before it breaks, in MPa. It matters for boards, tiles, and panels that span between supports.
- Float glass
- Standard flat glass, made by floating molten glass on a bath of molten tin. It is the base for most glazing.Read the guide on Float glassSee also Cullet, IGU
- FloorScore
- A US certification of low VOC emissions from hard-surface flooring and related products.Read the guide on FloorScoreSee also VOC
- Formaldehyde class
- A rating of how much formaldehyde a product emits, most relevant to wood-based panels and some adhesives. E1 is the common European class for panels and E0 is stricter. Japan's F-star grades run from F** to F****, the strictest.Read the guide on Formaldehyde classSee also VOC
- Frame material
- What a window or door frame is made of, such as timber, aluminium, aluminium-clad timber, steel, or uPVC. It affects thermal performance, maintenance, lifespan, and embodied carbon.See also uPVC, U-value
- Frost resistance
- How well a material survives repeated freezing and thawing while wet. Clay bricks, for example, are classed F0 to F2, with F2 suited to severe exposure.See also Water absorption
- FSCForest Stewardship Council
- A global certification for responsibly managed forests. Each certified company has a licence code that you can check against the public FSC database.Read the guide on FSCSee also PEFC, Chain of custody
- Functional unit
- A measure of what a product does rather than how much of it there is, such as 1 m² of wall insulation at a set U-value for 60 years. It allows a fairer comparison between different materials.Read the guide on Functional unitSee also Declared unit
- Future Homes Standard
- Updated energy and ventilation rules for new homes in England, published in March 2026 and applying from March 2027, subject to transitional arrangements. They target the energy used to run a home rather than embodied carbon.Read the guide on Future Homes StandardSee also Part L, Operational carbon
G
- g-valueSolar factor
- The share of the sun's heat that passes through glazing, from 0 to 1. A lower figure helps limit overheating, and a higher one captures more free winter heat.Read the guide on g-valueSee also Part O
- Gas fill
- The gas sealed between the panes of an insulated glass unit: air, argon, or krypton. Argon and krypton conduct heat less than air, so they lower the U-value. Krypton works in narrower gaps but costs more.See also IGU, U-value, Spacer type
- Generic data
- Carbon data drawn from industry averages or databases rather than measured for a specific product. It is useful early in a project, but it cannot show that one manufacturer's product is better than another's.Read the guide on Generic dataSee also Carbon benchmark, ICE Database, EPD
- Geopolymer
- A binder that replaces Portland cement, made by activating materials such as slag or fly ash with an alkaline solution. Its carbon saving depends heavily on the precursors and activators used.Read the guide on GeopolymerSee also GGBS, PFA
- GGBSGround granulated blast-furnace slag
- A by-product of ironmaking used to replace part of the cement in concrete, reducing its embodied carbon. It can slow early strength gain, so programmes may need adjusting.Read the guide on GGBSSee also PFA, Low-carbon concrete
- GLA whole life carbon assessment
- The Greater London Authority's requirement for referable planning applications in London to assess whole life carbon.Read the guide on GLA whole life carbon assessmentSee also Whole life carbon
- Glass type
- The kind of glass in a unit, such as float, toughened, laminated, low-e, acoustic, or obscured. Safety glass is needed in some places, such as low-level glazing and glazed doors.See also Float glass, Low-e glass, Glazing configuration
- Glazing configuration
- How a glazed unit is made up, such as the number and thickness of panes, cavity widths, gas fill, and coatings.Read the guide on Glazing configurationSee also IGU, Low-e glass
- Gloss levelGU
- How shiny a surface is, measured in gloss units. Low values are matt and high values are glossy.
- GlulamGlued laminated timber
- Structural beams and columns made by gluing timber layers together with the grain running in the same direction, which allows long spans.Read the guide on GlulamSee also CLT, Engineered timber
- Grain size
- The size of the particles in an aggregate, sand, or textured finish, in mm. It affects strength, drainage, and surface texture.
- Green Claims Code
- UK guidance from the Competition and Markets Authority requiring environmental claims to be truthful, clear, and backed by evidence. Since April 2025, the CMA has been able to enforce consumer law directly and impose fines.See also Greenwashing
- Green Guide to Specification
- A BRE reference rating common building specifications on their lifecycle environmental performance. Project teams now often rely on product and building LCA data instead.See also BREEAM, LCA
- Green roof substrate depth
- How deep the growing medium on a green roof is. Shallow substrates suit sedum, while deeper ones support grasses, wildflowers, and shrubs and hold more rainwater. A deeper substrate is heavier, so the roof must be designed for the load.See also Plant mix
- GREENGUARDGREENGUARD Gold
- A UL certification for products tested for low chemical emissions, intended to support healthier indoor air.Read the guide on GREENGUARDSee also VOC
- Greenwashing
- Making a product or company seem more environmentally friendly than the evidence supports. Vague wording, selective figures, and self-made labels are common signs.Read the guide on GreenwashingSee also Third-party verification
- Grown in Britain
- A UK licensing scheme that verifies timber and wood products were grown in Britain, and that the timber is legal and sustainable.See also FSC, PEFC, Local sourcing
- GTIN/EAN
- A globally unique product identifier, usually shown under a barcode. It helps catalogues, procurement, and stock systems identify the exact product.
- GWPGlobal Warming Potential, GWP-fossil, GWP-biogenic, GWP-luluc
- The EPD indicator measuring a product's contribution to climate change, reported in kgCO₂e. It is the headline number used to compare embodied carbon.Read the guide on GWPSee also CO₂e, EPD
H
- Hard wax oil
- A wood finish that blends natural oils and waxes to protect timber, and can often be spot-repaired without sanding the whole floor. Check the formulation for solvents.Read the guide on Hard wax oilSee also VOC
- Head or drive type
- The shape of a fixing's head, such as countersunk, pan, or hex, and the bit that drives it, such as Pozidriv, Torx, or hex.
- Hemp shivHemp hurd
- The woody inner core of the hemp stalk, chopped and used as the aggregate in hempcrete.Read the guide on Hemp shivSee also Hempcrete
- HempcreteHemp-lime
- A mix of hemp shiv and lime-based binder, used as insulating, moisture-regulating walling. It isn't load-bearing, so it is built around a structural frame.Read the guide on HempcreteSee also Bio-based, Breathable
- HPDHealth Product Declaration
- A standard format for disclosing a product's ingredients and their associated health hazards. Like Declare, it discloses content rather than certifying that a product is safe.Read the guide on HPDSee also Declare, Red List
- Hygroscopic
- Able to absorb moisture from the air and release it again. Materials such as clay plaster, timber, and wood fibre use this to help even out indoor humidity.Read the guide on HygroscopicSee also Moisture buffering, Breathable
I
- IAQIndoor air quality
- The condition of the air inside a building, as influenced by ventilation, moisture, and emissions from materials.Read the guide on IAQSee also VOC, Part F
- ICE DatabaseInventory of Carbon and Energy
- A widely used free database of typical embodied carbon values for construction materials, published by Circular Ecology. A common source of generic data for early estimates.See also Generic data, Carbon benchmark
- IGUInsulated glass unit
- Two or more panes of glass sealed together with a gas-filled or air-filled cavity between them, which is the standard double- or triple-glazed unit.Read the guide on IGUSee also Low-e glass, Triple glazing
- Impact sound (Lw)
- How much noise from footsteps and knocks transfers through a floor, in decibels. Lower is better, unlike most other acoustic figures.See also Sound reduction (Rw)
- Impact strength (Charpy)
- The energy a notched sample absorbs when struck and broken, in joules. It shows how tough a metal is, especially at low temperatures.
- Industry-wide EPDGeneric EPD, sector EPD
- An EPD reporting an average across several manufacturers. It shows typical impacts for a product type, but not the performance of one manufacturer's product.Read the guide on Industry-wide EPDSee also Product-specific EPD, Generic data
- Installation method
- How a product is fixed in place, such as floating, glued, or nailed for flooring. The method can affect reuse at the end of its life.See also Design for disassembly
- Interstitial condensation
- Water vapour condensing inside a wall, roof, or floor build-up, where it can't be seen. It can cause rot and damp, and is a main risk to check when insulating older buildings.Read the guide on Interstitial condensationSee also Vapour resistance (μ), Breathable
- ISO 14001
- An international standard for environmental management systems. It shows that a company manages its environmental impact systematically, not that its products are low impact.Read the guide on ISO 14001
J
- Janka hardness
- The force needed to press a steel ball halfway into a piece of wood, in newtons. Higher figures mean timber resists dents better, which is useful for flooring.
L
- LCALife Cycle Assessment
- A structured method for measuring the environmental impacts of a product or building across its life, set out in ISO 14040 and ISO 14044. It is the study behind every EPD.Read the guide on LCASee also EPD, Lifecycle modules
- LEEDLeadership in Energy and Environmental Design
- A US-origin green building rating system, used internationally and rated from Certified to Platinum. Its Materials and Resources credits reward products with EPDs and sourcing disclosures.Read the guide on LEEDSee also BREEAM
- LETILondon Energy Transformation Initiative
- A UK network of built-environment professionals whose guidance and embodied carbon targets are widely used as benchmarks.Read the guide on LETISee also RIBA 2030 Climate Challenge, Carbon budget
- Lifecycle costTotal cost of ownership
- The total cost of a product across its life, including purchase, installation, maintenance, replacement, and disposal.Read the guide on Lifecycle costSee also Service life
- Lifecycle modulesA, B, C, and D
- The stages used to report impacts: A1–A3 product, A4–A5 construction, B1–B7 use, C1–C4 end of life, and D for benefits beyond the building's life. Only compare figures covering the same modules.Read the guide on Lifecycle modulesSee also A1–A3, Module D
- Light transmission
- The percentage of visible daylight that passes through glazing or a translucent material. Higher means a brighter interior.Read the guide on Light transmissionSee also g-value
- Lime plaster, mortar, and renderNHL, natural hydraulic lime, limewash
- Lime-based finishes and binders long used in traditional buildings, which allow walls to manage moisture. Natural hydraulic lime (NHL) sets partly by reacting with water, and limewash is a thin lime paint.Read the guide on Lime plaster, mortar, and renderSee also Breathable, Portland cement
- Linoleum
- Resilient flooring made mainly from linseed oil, wood flour, and pine resin, usually on a jute backing. It should not be confused with vinyl.
- Living Building ChallengeLBC
- A demanding building certification from the International Living Future Institute, based on measured performance over a period of occupation.Read the guide on Living Building ChallengeSee also Declare, Red List
- Load rating
- The load a fixing or component is rated to carry safely, in N or kN. Check the base material and conditions it applies to.
- Local sourcing
- Buying materials from nearby producers, which can cut transport emissions and support local economies. Manufacturing usually matters more for carbon, so a local product isn't automatically lower carbon.Read the guide on Local sourcingSee also Traceability
- Low-carbon concrete
- Concrete with reduced embodied carbon, usually through cement replacements. There's no single definition, so ask for the figure and compare it against a benchmark.Read the guide on Low-carbon concreteSee also GGBS, PFA, Carbon benchmark
- Low-e glassLow emissivity
- Glass with a very thin coating that reflects heat back into a room, which reduces heat loss through glazing.Read the guide on Low-e glassSee also IGU, U-value
- Low-temperature flexibility
- The lowest temperature at which a roofing membrane can bend without cracking, in °C.
- LVLLaminated veneer lumber
- A strong structural timber made by bonding thin wood veneers together with the grain mostly in one direction.See also Engineered timber, Glulam
M
- Material grade / alloy
- The designation of a metal's composition and properties, such as S355 structural steel or 6063 aluminium. It tells you which standard and strength values apply.
- Material passport
- A record of the materials in a product or building, including what they are and where they are, so they can be recovered and reused later.Read the guide on Material passportSee also Design for disassembly
- Maximum service temperature
- The highest temperature a product can withstand in normal use without losing its stated performance, in °C.
- Maximum span
- The longest distance a beam, joist, panel, or deck can bridge between supports. It only holds for the loads the supplier stated, and a structural engineer should confirm the final design.See also Load rating
- MDFMedium-density fibreboard
- A smooth board made from wood fibres and a resin binder. Check its formaldehyde class and how the fibres are sourced.See also Formaldehyde class, OSB
- Melting point
- The temperature at which a metal turns from solid to liquid, in °C. It is not a measure of fire performance, because many metals weaken well before they melt.
- MgO boardMagnesium oxide board
- A cement-free mineral board used for walls and ceilings. Quality varies, and some boards have absorbed moisture and caused problems, so check for independent certification.Read the guide on MgO board
- Mineral silicate paintMineral paint
- Paint with a silicate binder that bonds chemically to mineral surfaces such as masonry, staying highly vapour open and durable.Read the guide on Mineral silicate paintSee also Breathable
- Mineral wool
- Insulation spun from molten rock or glass, including stone wool and glass wool. It is typically non-combustible and often contains recycled content.Read the guide on Mineral wool
- Minimum order
- The smallest quantity a supplier will sell in one order.
- Minimum pitch
- The shallowest roof slope a roofing product is approved for, in degrees. Below this, water may not drain safely.
- Mix ratio
- The proportions of the components in a wet-mixed product, such as binder to sand or powder to water. Altering it can weaken the result.
- MMCModern methods of construction
- Building approaches using offsite manufacture and prefabrication, from whole modules to panelised systems. They can reduce waste, though the overall benefit depends on the materials and transport involved.Read the guide on MMC
- Modern Slavery Act 2015
- UK law targeting forced labour and trafficking. Larger businesses must publish an annual statement on what they do to tackle it in their supply chains.Read the guide on Modern Slavery Act 2015See also Responsible sourcing
- Modified woodAccoya, Kebony, thermally modified timber
- Timber treated with heat or chemicals to improve its durability and stability, without using conventional biocides.See also Durability class (EN 350), Use class (treatment)
- Module D
- Reported credits for potential reuse, recycling, or energy recovery after a product's life. It is shown separately because the benefits depend on what actually happens in the future.Read the guide on Module DSee also Lifecycle modules
- Modulus of elasticityYoung's modulus
- How stiff a material is, or how much it resists stretching or bending under load, in GPa. A higher figure means less deflection.
- Mohs hardness
- A 1 to 10 scale of how well a mineral resists scratching, with talc at 1 and diamond at 10. It is used for stone and aggregates.
- Moisture buffering
- How well a material soaks up and gives back moisture as indoor humidity changes, reported in g/m²·%RH. A higher value means it does more to steady humidity.See also Hygroscopic
- Moisture content
- The amount of water held in a material, as a percentage. In timber, it should suit the end use, or the wood can shrink, warp, or decay.See also Shrinkage
- Mounting method
- How an acoustic panel is fixed, such as glued direct, hung on clips or battens, or suspended as a baffle or raft. Leaving an air gap behind the panel usually improves absorption of low-pitched sound.See also Sound absorption (αw)
- MVHRMechanical ventilation with heat recovery
- A ventilation system that brings in fresh air and captures heat from the outgoing air. It is common in airtight buildings.Read the guide on MVHRSee also Airtightness, Passivhaus
N
- Natural materials
- Materials that are minimally processed and come from plant, animal, or mineral sources. There is no single legal definition, so check what the claim covers.Read the guide on Natural materialsSee also Bio-based, Greenwashing
- natureplus
- An international quality label for building products, testing health, emissions, and environmental impact, with an emphasis on renewable and mineral raw materials.
- Net zero
- A state where emissions are cut as far as possible and any remainder is balanced by removals. For buildings, check whether a claim covers operational carbon only or embodied carbon too.Read the guide on Net zeroSee also Carbon neutral, Whole life carbon
- Number of coats
- How many coats a paint, oil, or finish needs to perform as stated. Coverage figures are usually given per coat, so multiply them to estimate how much to buy.See also Coverage, Recoat time
O
- ODPOzone depletion potential
- An EPD indicator for emissions that damage the stratospheric ozone layer.Read the guide on ODPSee also EPD
- Opening type
- How a window opens: fixed, casement, tilt and turn, sliding sash, sliding, or pivot. It affects ventilation, cleaning access, and whether the window can be used as a fire escape.See also Approved Document B
- Operational carbon
- Emissions from running a building, mainly heating, cooling, hot water, and electricity. It falls as buildings get more efficient and the grid decarbonises, which makes embodied carbon a larger share.Read the guide on Operational carbonSee also Embodied carbon, Whole life carbon
- Original period
- When a reclaimed item was first made, such as Victorian or 1930s. It helps match existing work in repairs and conservation, and it is often an estimate.Read the guide on Original periodSee also Reclaimed
- OSBOriented strand board
- A structural board made from layers of wood strands bonded with resin, commonly used for sheathing and flooring.See also MDF, Formaldehyde class
P
- Pack sizeUnits per pack
- How much product comes in one pack, by area, volume, weight, or number of pieces. It helps you work out the amount to buy and avoid waste.
- Panel build-up
- The layers in a wall, floor, or roof panel and their thicknesses, from one face to the other. For example, a SIP is two OSB boards with an insulation core between them.See also SIP, Timber frame
- Part FApproved Document F
- The part of the Building Regulations in England covering ventilation. It becomes more important as buildings get more airtight.See also Airtightness, IAQ
- Part LApproved Document L
- The part of the Building Regulations in England covering conservation of fuel and power. It sets the energy performance requirements, including U-value limits, for new and existing buildings.Read the guide on Part LSee also U-value, Future Homes Standard
- Part OApproved Document O
- The part of the Building Regulations in England that requires new residential buildings to limit overheating, influencing decisions on glazing, shading, and ventilation.Read the guide on Part OSee also g-value
- Part Z
- An industry-proposed addition to the Building Regulations that would require whole life carbon assessment and embodied carbon limits. It is a proposal, not law.Read the guide on Part ZSee also Whole life carbon, Future Homes Standard
- PassivhausPassive House, PHPP
- A building performance standard for very low energy use, achieved through insulation, airtightness, and heat-recovery ventilation. Certified components are tested for use in these buildings.Read the guide on PassivhausSee also Airtightness, Operational carbon
- PCRProduct Category Rules
- The specific rules for how an EPD is calculated for a product type. EPDs are most comparable when they follow the same PCR.Read the guide on PCRSee also EPD, EN 15804
- PEFCProgramme for the Endorsement of Forest Certification
- A global forest certification system that endorses national schemes, and is widely used for small and family-owned forests.Read the guide on PEFCSee also FSC, Chain of custody
- PERE and PENRERenewable and non-renewable primary energy
- EPD indicators showing how much renewable (PERE) and non-renewable (PENRE) energy a product's lifecycle uses, excluding energy stored in the material itself.Read the guide on PERE and PENRESee also EPD
- PFAPulverised fuel ash, fly ash
- A by-product of coal-fired power generation, used as a partial cement replacement in concrete. Supply is shrinking as coal plants close.Read the guide on PFASee also GGBS, Low-carbon concrete
- Phenolic insulation
- A rigid foam board based on phenolic resin, with very low thermal conductivity, so it can be used in thin build-ups.Read the guide on Phenolic insulationSee also PIR, Thermal conductivity
- PIRPolyisocyanurate
- A rigid foam insulation board made from petrochemicals, valued for its low thermal conductivity in thin build-ups. It generally has a higher embodied carbon per unit of performance than bio-based options.Read the guide on PIRSee also Thermal conductivity, Wood fibre
- Plant mix
- The species planted or seeded on a green roof, such as sedum, wildflower, or a biodiverse mix. Native species usually offer more value to local wildlife.See also Green roof substrate depth
- POCPPhotochemical ozone creation potential
- An EPD indicator for emissions that contribute to ground-level ozone, or summer smog.Read the guide on POCPSee also EPD
- Portland cementCEM I, OPC
- The standard cement used in most concrete. Making its clinker releases large amounts of CO₂, which is why cement replacements are such a focus.Read the guide on Portland cementSee also Cement replacement, GGBS
- Post-consumer recycled content
- Material recovered from products that have already been used, such as old glass or paper. It is generally viewed as more valuable than pre-consumer content, because it diverts actual waste.Read the guide on Post-consumer recycled contentSee also Pre-consumer recycled content, Recycled content
- Pre-consumer recycled contentPost-industrial
- Waste from manufacturing that is diverted into a new product. It excludes offcuts that a factory simply feeds back into the same process.Read the guide on Pre-consumer recycled contentSee also Post-consumer recycled content, Recycled content
- Pre-demolition audit
- A survey of a building before demolition, identifying which materials can be reused or recycled.Read the guide on Pre-demolition auditSee also Deconstruction, Reclaimed
- Prefabrication level
- How much of a system is made in a factory. A kit of parts is cut components assembled on site. Panelised systems arrive as flat walls and floors, volumetric systems as whole 3D modules, and hybrid systems mix the two.Read the guide on Prefabrication levelSee also MMC, Volumetric construction
- Previous use
- Where a reclaimed material came from and what it did there, such as a mill floor or a railway. It hints at how the material was treated and what it may have been exposed to.Read the guide on Previous useSee also Contaminant checks, Condition grade
- Product form
- The shape an insulation product comes in: batts (slabs that fit between studs or joists), rolls, rigid boards, or loose fill that is blown or poured. It decides where the product can be used and how well it fills gaps.See also Mineral wool, Cellulose insulation
- Product-specific EPDProduct family EPD, system-verified EPD
- An EPD for one manufacturer's product or family of products, which is stronger evidence for comparing products than an industry average. A family EPD averages similar products, so check the range it covers.Read the guide on Product-specific EPDSee also EPD, Industry-wide EPD
- Programme operator
- The organisation that runs an EPD scheme and publishes its EPDs, such as IBU, BRE, or EPD International. An EPD's registration number can be checked with its operator.Read the guide on Programme operatorSee also EPD
R
- R-valueThermal resistance
- How strongly a layer of material resists heat flow, in m²K/W, found by dividing its thickness by its thermal conductivity. Higher is better.Read the guide on R-valueSee also Thermal conductivity, U-value
- Rammed earth
- Walls formed by compacting damp subsoil in layers inside formwork. It offers high thermal mass and low processing energy when no cement is added.Read the guide on Rammed earthSee also Thermal mass, Unfired clay
- Rapidly renewable
- From a source that regrows on a short cycle, often defined as within ten years, such as hemp, cork, or bamboo.See also Bio-based
- RCARecycled concrete aggregate
- Crushed concrete from demolition, reused as aggregate. It is most common as fill and sub-base, and its use in structural concrete is more limited.Read the guide on RCASee also Secondary aggregate, Downcycling
- ReclaimedSalvaged
- Recovered from an existing building or site and reused with little processing, unlike recycled material, which is broken down and remade. Check its condition and suitability before specifying it.Read the guide on ReclaimedSee also Recycled content, Circular economy
- Recoat time
- The minimum wait before applying the next coat. It gets longer in cold or damp conditions, and a surface can feel dry to the touch before it is ready.See also Curing time, Number of coats
- Recycled content
- The percentage of a product, by mass, made from recycled material. Check how the figure is measured and whether the claim has been independently verified.Read the guide on Recycled contentSee also Post-consumer recycled content, Pre-consumer recycled content
- Red List
- The International Living Future Institute's list of chemicals and materials to avoid because of their harm to health or the environment. Declare labels show whether a product is free of them.Read the guide on Red ListSee also Declare, Living Building Challenge
- Residual emissions
- The emissions left after all practical reductions have been made, which then have to be balanced by removals or offsets to reach net zero.Read the guide on Residual emissionsSee also Net zero, Carbon offset
- Responsible sourcing
- Managing the environmental and social impacts of materials across the supply chain, from extraction and labour conditions to transport.Read the guide on Responsible sourcingSee also BES 6001, Traceability
- ResponsibleSteel
- A global standard and certification covering environmental, social, and governance performance at steel sites, with further requirements for steel products.Read the guide on ResponsibleSteel
- Retrofit
- Upgrading an existing building to reduce its energy use and improve comfort. In the UK, PAS 2035 is the standard framework for whole-house domestic retrofit.Read the guide on RetrofitSee also Interstitial condensation, Breathable
- Reused content
- The percentage of a product made from components reused without being reprocessed, as distinct from recycled content.See also Reclaimed, Recycled content
- RIBA 2030 Climate Challenge
- A voluntary set of targets from the Royal Institute of British Architects for reducing operational energy, embodied carbon, and water use by 2030.Read the guide on RIBA 2030 Climate ChallengeSee also LETI, Whole life carbon
- RICS whole life carbon assessmentWLCA, WLC
- The professional standard from the Royal Institution of Chartered Surveyors that sets out how to assess a building's whole life carbon in the UK.Read the guide on RICS whole life carbon assessmentSee also Whole life carbon, EN 15978
S
- Safety Data SheetSDS
- A supplier's document setting out a product's hazards and how to handle, store, and dispose of it safely, and what to do in an emergency.See also COSHH
- SAPStandard Assessment Procedure
- The UK government's method for calculating the energy performance of homes, used to show compliance with Part L and to produce Energy Performance Certificates.Read the guide on SAPSee also Part L
- SBTiScience Based Targets initiative
- An organisation that validates companies' emissions targets against climate science. A validated target is a commitment, not proof that reductions have been achieved.Read the guide on SBTiSee also Scope 1, 2, and 3
- SCMSupplementary cementitious material
- A material that replaces part of the cement in concrete, such as GGBS, fly ash, calcined clay, or silica fume.Read the guide on SCMSee also GGBS, PFA, Cement replacement
- Scope 1, 2, and 3
- Categories of a company's emissions: scope 1 is direct, scope 2 comes from purchased energy, and scope 3 is everything else in its value chain. The embodied carbon of materials a company buys usually falls in its scope 3.Read the guide on Scope 1, 2, and 3
- Sd valueEquivalent air layer thickness
- How much a layer resists water vapour, expressed as the depth of still air that would resist it equally, in metres. It equals the μ value times the thickness, and a lower figure is more vapour open.See also Vapour resistance (μ), Breathable
- Secondary aggregate
- Aggregate made as a by-product of another industry, such as slag or china clay waste, rather than recovered from demolition.Read the guide on Secondary aggregateSee also RCA, By-product
- Security class
- A rating of how well a window or door resists forced entry, such as RC classes under EN 1627 or the UK's PAS 24.
- SequestrationCarbon storage
- Drawing carbon out of the atmosphere and holding it, for example in growing trees or in materials made from them. The benefit lasts only while the carbon stays stored.Read the guide on SequestrationSee also Biogenic carbon
- Service lifeDesign life, reference service life, RSL
- How long a product is expected to perform in use, in years. A longer life can outweigh a higher initial carbon figure, because the product is replaced less often.Read the guide on Service life
- Setting time
- How long a wet mix takes to stiffen and start hardening. It comes before curing, which is when the mix gains its full strength.See also Curing time, Working time
- Shear strength
- How much stress a material or joint can take from forces sliding its layers past each other, in MPa.
- Sheep's wool insulation
- A natural-fibre insulation that handles moisture well. Check the treatments used against pests and any synthetic binder.Read the guide on Sheep's wool insulationSee also Bio-based, Hygroscopic
- Shore hardness
- The hardness of rubbers and plastics, based on indentation. Shore A is used for softer materials and Shore D for harder ones.
- ShrinkageTangential, radial
- How much timber shrinks as it dries, as a percentage. Tangential shrinkage runs along the growth rings and is usually greater than radial shrinkage, which runs across them.See also Moisture content
- Silica fume
- A very fine by-product of silicon and ferrosilicon production, used in concrete to increase strength and reduce permeability.Read the guide on Silica fumeSee also SCM
- SIPStructural insulated panel
- A prefabricated panel with an insulating core between two structural facings, usually OSB, used for walls and roofs.Read the guide on SIPSee also OSB, MMC
- Slip resistancePendulum (PTV), R rating
- How much grip a floor surface offers, given as an R rating from a ramp test (R9–R13) or a Pendulum Test Value. For PTV, the UK generally treats 36 or above as low slip risk.
- Smoke class
- The part of a Euroclass rating that covers smoke production in a fire, from s1 (least smoke) to s3 (most).See also Euroclass, Flaming droplets
- Solar reflectance indexSRI
- How well a surface stays cool in the sun, combining how much heat it reflects and how much it re-emits. Standard black scores about 0 and standard white about 100.See also g-value
- Sound absorption (αw)
- How much sound a surface soaks up instead of reflecting, on a scale from 0 to 1. It helps reduce echo within a room but doesn't stop sound travelling to the next one.See also Sound reduction (Rw)
- Sound reduction (Rw)
- How well a wall, floor, or window blocks airborne sound in laboratory tests, in decibels. Higher is better, and results on site are usually lower.See also Impact sound (Lw), Sound absorption (αw)
- Spacer type
- The strip that holds the panes of an insulated glass unit apart around the edge. Aluminium spacers conduct heat and leave the edge colder. Warm edge spacers reduce heat loss and condensation at the edge.See also IGU, Thermal bridge, Gas fill
- Specific heatSpecific heat capacity
- The energy needed to heat 1 kg of a material by one degree, in J/kgK. Together with density, it determines how much heat a material can store.See also Thermal mass, Density
- StandardBS, EN, ISO
- The published document a product was made or tested to. BS marks a British Standard, EN a European one, and ISO an international one, and they are often combined, as in BS EN ISO.
- Straw bale
- Compressed bales of straw, an agricultural by-product, used as insulation within a frame or sometimes as load-bearing walls. They need good detailing to stay dry.Read the guide on Straw baleSee also Bio-based
- Strength class
- A standard grade of structural strength, such as C24 for timber or C30/37 for concrete. Engineers design to these classes.
- Suitable substrate
- The base materials a product is designed to fix to or go onto, such as timber, masonry, concrete, or plasterboard. Using it on anything else can cause it to fail.
- Surface finishColour
- A product's colour and surface texture as supplied, such as brushed, oiled, or matt. Finish can vary between batches, so ask for a sample.
- System boundary
- What an LCA or carbon figure includes and leaves out, such as which lifecycle modules it covers.Read the guide on System boundarySee also Lifecycle modules
T
- Tear strength
- How much force it takes to tear a membrane or geotextile, in kN/m or N/mm.
- Tensile strength
- The maximum pulling stress a material can take before it breaks, in MPa.See also Yield strength
- Thermal bridge
- A spot where heat escapes more easily through the building fabric, such as at a junction or where a structural element crosses the insulation. It adds heat loss and can cause cold spots and condensation.See also U-value, Interstitial condensation
- Thermal conductivityLambda (λ)
- How readily heat passes through a material, in W/mK. Lower is better for insulation, and a thicker layer of a higher-lambda material can match a thinner one.Read the guide on Thermal conductivitySee also R-value, U-value
- Thermal mass
- A material's ability to absorb and slowly release heat. Heavy materials such as earth, brick, and concrete can smooth out temperature swings in a building.Read the guide on Thermal mass
- Third-party verification
- An independent check of a claim or dataset by an organisation with no stake in the result. It is the main difference between evidence and a manufacturer's own statement.Read the guide on Third-party verificationSee also EPD, Greenwashing
- Timber frame
- A building structure of timber studs and panels that carries the loads, with insulation typically held between the studs.See also Engineered timber, MMC
- Timber species
- The type of tree the wood comes from, such as European oak or Douglas fir. Species affects strength, durability, and appearance, and is needed for legal and certification checks.See also Durability class (EN 350), UKTR
- Traceability
- The ability to follow a material back through its supply chain to where it came from, supported by documents rather than general statements.Read the guide on TraceabilitySee also Chain of custody, Responsible sourcing
- Traffic class
- The heaviest traffic a paving product is meant for: pedestrians, light vehicles, or heavy vehicles. The sub-base and how the paving is laid matter as much as the product itself.See also Water permeability, Load rating
- Triple glazing
- A glazed unit with three panes, offering a lower U-value than double glazing but with more glass, weight, and embodied carbon.Read the guide on Triple glazingSee also IGU, U-value
- TVOCTotal volatile organic compounds
- The combined level of VOCs a product emits, often tested after 28 days, in μg/m³. Lower means less off-gassing into indoor air.Read the guide on TVOCSee also VOC
- Type I ecolabel
- A label awarded by an independent third party against published criteria, under ISO 14024. Self-declared claims and EPDs fall under different types.See also EU Ecolabel, Blue Angel, EPD
U
- U-value
- The rate of heat loss through a whole building element, such as a wall or window, in W/m²K. Lower is better, and it is the figure Building Regulations set limits on.Read the guide on U-valueSee also R-value, Thermal conductivity, Part L
- UK Net Zero Carbon Buildings StandardUKNZCBS
- A voluntary, cross-industry UK standard setting out what a net zero carbon building must achieve, covering energy use and embodied carbon. Version 1 was published in March 2026.See also Net zero, Whole life carbon
- UKASUnited Kingdom Accreditation Service
- The UK's national accreditation body, which assesses the certification bodies and laboratories themselves. UKAS accreditation is a sign a certificate can be relied on.Read the guide on UKASSee also Third-party verification
- UKGBCUK Green Building Council
- A UK membership organisation for the built environment that publishes guidance on net zero buildings and sustainability.Read the guide on UKGBCSee also UK Net Zero Carbon Buildings Standard
- UKTRUK Timber Regulation
- Rules prohibiting illegally harvested timber from being placed on the UK market, with due diligence duties for businesses placing it there first.Read the guide on UKTRSee also FSC, PEFC
- Underfloor heating compatibilityUFH
- Whether a floor covering can go over underfloor heating: suitable, suitable with limits, or not suitable. Limits are often a maximum surface temperature, commonly around 27°C for wood. Thick or insulating coverings also reduce how much heat comes through.See also Thermal conductivity
- Unfired clay
- Clay plasters, boards, and bricks that are dried rather than kiln-fired, which saves a great deal of energy. They also help regulate indoor humidity, but they must be kept away from persistent wetting.Read the guide on Unfired claySee also Hygroscopic, Rammed earth
- Uniclass
- A standard UK construction classification, maintained by NBS, used to structure specifications, BIM, and product information.See also BIM
- Upcycling
- Reusing or reprocessing waste into a product of equal or higher value than the original.Read the guide on UpcyclingSee also Downcycling
- Upfront carbonA1–A5, cradle to handover
- Emissions released before a building is occupied, covering lifecycle modules A1–A5. These are locked in at completion, which is why material choices matter so early.Read the guide on Upfront carbonSee also Embodied carbon, Lifecycle modules
- uPVCUnplasticised polyvinyl chloride, PVC
- A rigid plastic widely used for window frames and pipework. Its durability and low maintenance are weighed against fossil-based content and end-of-life concerns.Read the guide on uPVC
- Use class (treatment)
- The exposure conditions timber is treated for under EN 335, from use class 1 (dry interior) to use class 5 (sea water).See also Durability class (EN 350)
- UV resistance
- How well a material keeps its strength and appearance under sunlight. It matters for external finishes, plastics, and exposed membranes.
V
- Vapour resistance (μ)
- How strongly a material resists water vapour compared with still air. A low μ value means vapour passes through easily, which helps a construction dry out.Read the guide on Vapour resistance (μ)See also Breathable, Interstitial condensation
- Vickers hardnessHV
- A metal's resistance to indentation, measured by pressing a diamond pyramid into its surface. A higher number means a harder metal.See also Brinell hardness
- Virgin material
- Raw material that is newly extracted or harvested and hasn't been used before. It isn't always the worse option, as some uses need its performance or have no viable alternative.Read the guide on Virgin materialSee also Recycled content, Reclaimed
- VOCVolatile organic compound
- A carbon-based chemical that evaporates into the air at room temperature, commonly from paints, adhesives, and finishes. High levels can affect indoor air quality and health.Read the guide on VOCSee also TVOC, GREENGUARD
- VOC content
- How much VOC a product contains, in grams per litre. This differs from emissions, which measure what is actually released into a room over time.Read the guide on VOC contentSee also VOC, VOC emissions class
- VOC emissions classFrench A+ scale
- A rating of a product's emissions into indoor air on the French scale from C to A+, where A+ has the lowest emissions.Read the guide on VOC emissions classSee also VOC, TVOC
- Volumetric constructionModular construction
- A type of offsite construction in which whole three-dimensional modules are built in a factory and assembled on site.Read the guide on Volumetric constructionSee also MMC
W
- Waste hierarchy
- The order of preference for handling waste: prevention, then reuse, recycling, other recovery, and disposal as a last resort.Read the guide on Waste hierarchySee also Circular economy
- Water absorption
- How much water a material takes up, as a percentage of its weight. It affects frost resistance, staining, and insulation performance.See also Frost resistance
- Water permeability
- How quickly water drains through a material, in mm/h or l/s/m². It matters for permeable paving and landscaping.
- Watertightness class
- How well a window or door keeps out driving rain under test, classified under EN 12208. A higher number means it holds out at a higher test pressure.See also Air permeability class, Wind resistance class
- Wear layer thickness
- The thickness of a floor's top, usable layer, in mm. On engineered wood, a thicker hardwood layer can be sanded back more times. On vinyl and LVT, a thicker clear layer protects the printed surface for longer.See also Engineered timber, Abrasion class
- WeightWeight per area
- How heavy a product is, in total or per square metre. It affects handling, transport, and structural loads.
- WELLWELL Building Standard
- A building certification centred on occupant health and wellbeing, including air, water, light, and materials.Read the guide on WELLSee also VOC
- Whole life carbon
- The total emissions of a building over its life, combining embodied and operational carbon. In the UK it is usually assessed using the RICS professional standard.Read the guide on Whole life carbonSee also Embodied carbon, Operational carbon
- Wind resistance class
- How well a window or door withstands wind load under EN 12210, with a number for pressure (1 to 5) and a letter for frame deflection (A to C).See also Air permeability class, Watertightness class
- Wood fibre
- Insulation made from softwood fibres, often forestry and sawmill residues, supplied as boards or flexible batts. It is vapour open and adds useful thermal mass compared with lightweight insulation.Read the guide on Wood fibreSee also Bio-based, Breathable
- Working timePot life
- How long a mixed product stays usable before it starts to stiffen. Heat can shorten it.See also Setting time, Curing time
X
- XPSExtruded polystyrene
- A dense, moisture-resistant foam insulation board, often used below ground and in inverted roofs.Read the guide on XPSSee also EPS, PIR
Y
- Yield strength
- The stress at which a material starts to deform permanently, in MPa. Where there is no clear yield point, it is usually taken at 0.2% offset.See also Tensile strength
Missing a term?
Tell us what you came across and we'll look at adding it. For certifiers and tools, see the certification directory.